Jump to content
Vari-Lite Controls Support Forum

FLX control via Midi.


Uriahdemon

Recommended Posts

30 minutes ago, Edward- Z88 said:

Setup -> Triggers, MIDI Notes is set to playbacks, and the Channel is left at 0 (to receive Notes commands from all channels), or set to the channel number set on the Novation.

Your octaves will likely be set to "Separate", to give you access to playbacks 0 to 127.

Almost certainly that, not absolutely sure about Channel but, if it isn't 0 then it probably should be.  :)

Link to comment
Share on other sites

  • Replies 74
  • Created
  • Last Reply

Top Posters In This Topic

Hi David,

Given all this great advice I now have my FLX and Launchpad set up and have MIDI control.  I am using the files you sent over so need to adjust the playbacks on the FLX for notes 1-64 to trigger what I need and of course my own colours.

There is one question please on Note #1 on the top row furthest left.  That is triggering PB2 as opposed to PB1 have you any idea why that may be happening please.... did you come across that and just ignore PB 1.......??

Apart from that they are all triggering the PB's in sequence.

Rgds Mac

 

Link to comment
Share on other sites

Hi Mac,

3 minutes ago, Uriahdemon said:

That is triggering PB2 as opposed to PB1 have you any idea why that may be happening please.... did you come across that and just ignore PB 1.......??

MIDI Notes 0, will trigger playback 1, and MIDI Note 1 will trigger playback 2 and so on.

This may be what you are seeing?

Edward

Edward Smith
Product Specialist

Link to comment
Share on other sites

4 minutes ago, Uriahdemon said:

Hi David,

Given all this great advice I now have my FLX and Launchpad set up and have MIDI control.  I am using the files you sent over so need to adjust the playbacks on the FLX for notes 1-64 to trigger what I need and of course my own colours.

There is one question please on Note #1 on the top row furthest left.  That is triggering PB2 as opposed to PB1 have you any idea why that may be happening please.... did you come across that and just ignore PB 1.......??

Apart from that they are all triggering the PB's in sequence.

Rgds Mac

 

I think I may have found it....  seems the midi notes start at Zero i.e. a 'C' so Zero (0) is triggering PB1

Link to comment
Share on other sites

Hi Mac,

1 minute ago, Uriahdemon said:

Indeed it is Ed,  just sussed that out this end.....  thanks for your help  !!!!

No problem - in a future update we will ensure MIDI Notes are patched 1:1 with playbacks, which will also allow the Master Playback to be triggered.

Edward

Edward Smith
Product Specialist

Link to comment
Share on other sites

  1. Now you two have me worried that my setup is wrong. I thought button one was c# and triggering pb1. I'll have to get my desk out and see what I've done.

I haven't been able to try it on stage yet although the 1-64 file is an amended version of one I've used on a few live shows so it ought to have been right. The desk is still on the last-but-one version of ZerOS - don't know if that makes a difference. It thought it looked OK on Capture though.

Apologies for any inconvenience caused though.

 

 

Edited by Davidmk
Typo
Link to comment
Share on other sites

6 minutes ago, Davidmk said:
  1. Now you two have me worried that my setup is wrong. I thought button one was c# and triggering pb1. I'll have to get my desk out and see what I've done.

I haven't been able to try it on stage yet although the 1-64 file is an amended version of one I've used on a few live shows so it ought to have been right. The desk is still on the last-but-one version of ZerOS - don't know if that makes a difference. It thought it looked OK on Capture though.

Apologies for any inconvenience caused though.

 

 

No inconvenience caused at all David given all you and Ed have input to this.  Now it is my turn to do you a favour.  If you give me a couple of days I will re-map the 1-64 PB's and of course include PB1.  I will send a copy over to you but you will of course have to update your colouring.

Link to comment
Share on other sites

Hi David,

26 minutes ago, Davidmk said:

The desk is still on the last-but-one version of ZerOS - don't know if that makes a difference. It thought it looked OK on Capture though.

This has been how MIDI Notes has operated on ZerOS since it was introduced - the first note (note 0) triggering playback 1. Therefore if your configuration was working, a software update won’t change that.

So not sure where the problem Mac has found has arisen from?

When we do come to map the MIDI Notes 1:1 with playback’s, you will need to remap your set up.

Edward

Edward Smith
Product Specialist

Link to comment
Share on other sites

OK now I'm more confused. Attached screenshot shows midi note-on arriving and what happened on the playback LEDs.

The wing was showing page 1, the desk page 6 (where the pb/cue triggered by pb1/cue 1 is located). It behaved as expected and the correct cue was triggered so pb LED 25 is presumably pb1.

The above suggests note 1 triggers pb 1 which does not tally with what Edward said

6 hours ago, Edward- Z88 said:

MIDI Notes 0, will trigger playback 1

therefore I must be misunderstanding something.

I've stopped playing with the desk (I'm a fan of Vera on ITV right now) but I've left it set up and I'll continue tomorrow. One thing I'll be looking at is advice I had when first playing with notes, something about a setting which I can't find now. Dont read too much into that, it was last year sometime and an even earlier version of ZeroOS.

20201016_200929.jpg

Link to comment
Share on other sites

115839602_MIDINoteNumbersNames1.thumb.png.41ce8e9c6abb2eeef5ecd61e0e8aa587.pngHi David,

I was simply going by the info in the pix.

Components - shows top left button = PB1 with Note value of C# and Octave value of -2.

But according to the midi notes chart the first midi note is 0 (Zero) and value is C and Octave value of -2.

For me I tested this and my PB1 is now triggering fine.  I even downloaded your file again to ensure I had not loaded a file that I had been messing around with.

Untitled.thumb.jpg.a6d01c22aad037e5cad32785198c431d.jpg

Link to comment
Share on other sites

I've got the same for the first button but it fires pb1 not two. Edward said midi 0 would fire pb1 and you said midi 1 was firing pb2 1 if that is true then my desk must be operating in a parallel universe (or, being 2 versions behind is making the difference).

I'll play some more after I've walked the dogs.

Screenshot 2020-10-16 203241.jpg

Link to comment
Share on other sites

Hi David,

2 hours ago, Davidmk said:

I've got the same for the first button but it fires pb1 not two. Edward said midi 0 would fire pb1 and you said midi 1 was firing pb2 1 if that is true then my desk must be operating in a parallel universe (or, being 2 versions behind is making the difference).

I reckon I have worked out where the confusion may be. If you tap SETUP -> Triggers -> Combine Octaves, what is your “First Note” set to? By default, this should be 0. This will mean in Channels, a Note 1 triggers fixture 1, in Cues Note 1 triggers cue 1, and in Playbacks Note 0 triggers playback 1. If you have the First Note set to 1, and then click Separate Octaves, in Playbacks Note 1 will trigger playback 1. Note 0 will have no function. 

Could this be what you’re seeing?

If so, to save @Uriahdemon remapping all the Novation buttons, you can tap Combine Octaves, change the First Note to 1, and then click Separate Octaves.

Edward

Edward Smith
Product Specialist

Link to comment
Share on other sites

4 minutes ago, Davidmk said:

Why doesn't it show up on separate octaves? Bug, surely

Correct. Unfortunately the “First Note” field is applicable for “Separate Octaves”, however is incorrectly hidden when Separate Octaves is chosen. Logged on our system, to be fixed in a future update. Most people will just live in “Separate Octaves” with the default of the First Note of 0.

Edward

Edward Smith
Product Specialist

Link to comment
Share on other sites

4 hours ago, Edward- Z88 said:

Hi David,

I reckon I have worked out where the confusion may be. If you tap SETUP -> Triggers -> Combine Octaves, what is your “First Note” set to? By default, this should be 0. This will mean in Channels, a Note 1 triggers fixture 1, in Cues Note 1 triggers cue 1, and in Playbacks Note 0 triggers playback 1. If you have the First Note set to 1, and then click Separate Octaves, in Playbacks Note 1 will trigger playback 1. Note 0 will have no function. 

Could this be what you’re seeing?

If so, to save @Uriahdemon remapping all the Novation buttons, you can tap Combine Octaves, change the First Note to 1, and then click Separate Octaves.

Edward

Just the ticket, thanks Ed

Link to comment
Share on other sites

1 hour ago, Uriahdemon said:

dymo label maker

Yep, tried that, and transparent printer labels. Thought about trying sandpaper to give some grip and/or wiping the keys with meths before applying labels. Suppose you could cling film it and put labels on that.

Do they make keyboard protectors (like you get for keyboards or tills in bars) for it?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.