mikeb
-
Posts
195 -
Joined
-
Last visited
-
Days Won
2
Community Answers
-
mikeb's post in Ipad Mini was marked as the answer
Steve,
The iPad software has the same five desktop views as the console and also has a panel and wheel view too. I don't have an iPhone so can't comment one with the remote software.
I favour using the iPad to remotely fine-tune positions and fade in/out generic lights for focusing, leaving the iPad at stage level if working at height from zarges. Each desktop view can open different palettes where I like having four quarter screen ones on my main display with two half screen width ones on the iPad. It would be possible to use the iPad whilst programming using palettes but would depend on your preference of what views were open. That said, even if four palettes open at the same time was a little difficult, you can have four or more palette/views at full screen available at the touch of a tab at the bottom of the desktop screen - you can also have individual palettes on different desktops too, so things are pretty flexible and can be set how you want them.
Attached are three photos showing iPad mini and iPad;
zeros1.jpg is the panel view seen for a Solution console - the Solution XL has smaller graphics because of the extra faders
zeros2.jpg is a view I set on Desktop 1 for Memories and Submasters
zeros3.jpg is a view on Desktop 2 for the Colour, Effect, Beamshape and Position palettes
Hopefully this is helpful
Mike
-
mikeb's post in Fixture File for Chauvet Slimpar Tri 7 & 12 IRC was marked as the answer
Hiya,
Please find attached file for 3 and 7 DMX channel modes.
I believe the 7 channel mode is Ok but welcome verification
Please reply if you find any problems with the file.
Regards
Mike
Chauvet_Slimpar.ift
-
mikeb's post in Martin SCX700 Mode 2 on Jester 24 What does what was marked as the answer
Roy,
From what I can see the M2 mode of the fixture profile has 10 DMX channels;
Colour: Color1
Beamshape: Shutter, Gobo1, G1 Rotate, Macro, FX Mac and FX Speed
Position: Pan, Tilt, P/T Speed
I predominantly use a Solution XL or Frog console so forgive me if this is something that you've already tried, but each aspect whether Colour, Beamshape or Position can have multiple "layers". This means that you press the attribute button, in this case Beamshape, more than once to view all the available options.
Hope this is of use.
Regards
Mike
-
mikeb's post in release notes can not be downloaled? was marked as the answer
Hi there.
Looks like the link needs updating...
That said, the 10.12 software and phantom offline editor is available from the Frog Range Software release page;
http://zero88.com/support/index.php?/de/Knowledgebase/Article/View/56/257/frog-range-operating-software-release-1012
Regards
Mike
-
mikeb's post in Chauvet Slimpar Pro Vw was marked as the answer
Hi Ben
I've downloaded the manual and have created a fixture file for you. If you can take a look and see if it's Ok.
Let me know of any problems.
Regards
Mike
I've updated the fixture file for 3 DMX and 2 DMX modes - Regards Mike
Chauvet.ift
-
mikeb's post in Fixture Wihout Brightness was marked as the answer
R
Not sure if I remember my DMX channels correct but I have created a fixture file.
DMX 1 - R, DMX 2 - G, DMX 3 - B, DMX 4 - Fixed Colours, DMX 5 - Strobe and DMX 6 - Macro (Sound to Light?)
When loaded, I believe you should see a virtual dimmer in the Beamshapes section.
Let us know if you have any problems.
Regards
Mike
Generic.ift
-
mikeb's post in Fixture Profile Showtec was marked as the answer
PFA...
Ok, the manual is a little confusing when it says;
- DMX 2 Strobe, Shutter Closed and Slow to Fast - but Shutter should be open and static.
- DMX 5 Gobo Rotate @ 128-191 picture shows Low Speed to Fast but text shows Fast to Slow
- DMX 6 Prism @ 8-132 picture shows Low Speed to High Speed but text shows High to Low
Let me know if I need to make adjustments
Regards
Showtec.ift
-
mikeb's post in Betapack 2 Analogue Connector was marked as the answer
Richard,
Those are the connectors I have for connecting a demux to my betapacks.
If you haven't got the spec for what connection is on what pin then this may be of use;
Zero88: Pin 1-> Ch1, Pin 2 -> Ch2, Pin 3 -> Ch3, Pin 4 -> Ch4, Pin 5 -> Ch5, Pin 6 -> Ch6, Pin 7 -> Supply and Pin 8 -> Ground.
Hope that helps
Mike
-
mikeb's post in American Dj Inno Color Beam Quad 7 was marked as the answer
Hi there,
You can try the attached 13 channel DMX personality. I've not included an image of the fixture, so it should work on both USB and floppy consoles.
Regards
Mike
ADB ColorBeam Quad.ift
-
mikeb's post in Miltec Par144Qs/b was marked as the answer
Hi Terry,
I can't attach the detailed DMX info from Miltec as it's too big but I have attached an IFT that I've compiled. The attached is for the newer desks as I've included a fixture image. Reply back if you need an IFT for the older floppy based Frog desks.
I've created personalities for RGBW and RGBA fixtures - hope they're Ok.
Regards
Mike
MilTec LEDHead.ift