Jump to content
Vari-Lite Controls Support Forum

SimonH

Regulars
  • Posts

    129
  • Joined

  • Last visited

  • Days Won

    2

Everything posted by SimonH

  1. That is really sad news, he has only just had my desk in for repair and in my short dealings with him, he was a delight to deal with. Condolences. Simon
  2. SimonH

    FLX repairs

    Thanks all. I have messaged Ian.
  3. SimonH

    FLX repairs

    Where are people sending their desks for repair? Sub 24 has become very unstable and never reaching 100% . We also have an older desk that could do with some general tlc. Thanks, Simon
  4. What addresses are you using? Are you using RDM? I've had issues with non RDM fixtures flashing even if the console has RDM disabled as I think (Edward correct me if I'm Wrong) the Gateway 4 still transmits the RDM signal unless disabled in it's own config.
  5. Ok thanks for that, will give it a go edit: just checked and my stick is already FAT32 but it is a USB 3.0
  6. Hi, This is an old post and I wondered if there was any update on the size of USB? I carry a 192Gb on my keyring for all my handy bits and pieces and it doesn't seem to want to read that? Is it limited to USB 2?
  7. SimonH

    QLab

    Ok found the midi notes so I’ll phrase it differently. is it possible to trigger individual cues in the flx via midi but to include point cues and still be able to see the cue stack you are running?
  8. SimonH

    QLab

    Is there a guide for using Qlab to trigger a cue stack in the flx?
  9. Think it's only you and me on here!!
  10. Thought this place might be dead and forgotten but finally managed to log in. Very quiet and lonely here though.
  11. Is this a thing or are you referring to the list of wants? when I said list I meant the one you were working on not our would be nice list. thanks
  12. Can you tell me if the custom screen settings is on the list and where abouts roughly please? As far as usability for me this is the biggest hinderance during a plotting session. Thanks
  13. Thanks for the reply. I’ve sorted it now, my fat fingers had typed the wrong ip. still like to know where the reset button is though.
  14. Hi, ok used dmx workshop to change the IP address to 192.168.15.200 and now cannot see it anywhere. The instructions on here say to return to factory settings press reset button and cycle power but there isn’t a reset button or any button for that matter. help please.
  15. Thanks yet again Edward. perhaps a line in the instructions sent out with the unit should say please consult zeros manual for configuration on a console?
  16. I’ve just received my new gateway 4 and in the introduction it says it can be configured from the board or alternatively via a browser but in the configuration section there is no mention of setting it via the board. Am I missing something?
  17. So I emailed the tech support on the chauvet website asking for the info. I get an email from customer support asking tech support if they can help followed by reply from tech support saying this was a product support problem followed by an email from customer support saying they would ask product support and get back to me. You couldn't write this stuff.
  18. Thanks Edward, will give this a try. If I create a default show file from this and then a company change the addresses and modes can I then load this show and press recover rig and it should reset the RDM fixtures back to that show file?
  19. Thanks Edward, Hope Plasa is going well. It's been many years since I attended. Shouldn't the fixtures work with this basic personality?
  20. Hi, I have done a factory reset on the desk and then enabled Rigsync both globally and on each universe. It discovers all the compatible devices available and correctly identifies make and model but does not assign the correct fixture profile and so makes the fixtures unusable. When I try and change the fixture profile it says no alternative profies available. I have attached my test show file. rdm test.zos
  21. SimonH

    RDM

    I think I'm going to pause this until we receive our new gateway 4 and I will do some testing after that.
  22. SimonH

    RDM

    Hi, we have just bought some new wall mount Swisson dmx splitters that allow RDM transmission and have put the first one in direct from the dmx port on the back of the desk. the RDM light on the side of the Swisson is doing the same thing as the Artnet device which makes me think that the desk isn’t outputting RDM all the time. the Swisson instructions say the led should be solid ( same as the transcension). any help?
  23. SimonH

    RDM

    That’s great thanks Edward.
  24. SimonH

    RDM

    Hi, not sure I have 100% faith in the unit we have so looking at changing. The Swisson unit only says compatible with Artnet 1,2&3 but I think flx works with 4 is that correct? ideally I’d use a gateway 4 but it’s a little more expensive. thanks
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.