Edward Z88

Hi @simzee47 This functionality was removed several versions ago. Chases will ignore all cue fade, delay, and auto timings set in a playback. To use the cue timings rather than BPM, you will need to revert the playback from a chase, and then add "Auto After" triggers to each cue in the playback. Please see the link below for more information... https://www.zero88.com/manuals/zeros/cues-playbacks/cue-settings/cue-triggers The playback will then run through the cue timings and loop automatically. Please let me know if you have any questions.

Ah yep, a dedicated Inhibit is the way to go then 👍🏼

Yep, it does.

There have been occasions where I've needed to do this. In these situations, I raise my special playback, and simultaneously lower my Master Playback's fader, until I've got the balance how I want it. Is there a particular reason you don't want to touch the Master Playback in this situation? As @Davidmk mentions, Inhibit is essentially a Grand Master for certain fixtures. You cannot "release" the Grand Master - it always governs the overall intensity output from the console. This is therefore the same behaviour of an inhibit playback - the Trigger On Raise & Release On Lower options are irrelevant, so are greyed out.

Really pleased to hear you were able to recover the console using the ZerOS Start-up Tool. Please drop us an email to support@zero88.com if you have any questions. It is extremely unlikely for the OS to have corrupted. My guess is that the show file that was on the console had corrupted. As a side note, FLX S consoles cannot be recovered using a bootable USB drive. FLX S consoles must use the start-up tool for recovery.

The ZerOS Online Manual has been updated to reflect the changes and new features introduced in ZerOS 7.14.1... https://www.zero88.com/manuals/zeros A full list of revisions is available here... https://www.zero88.com/manuals/zeros/introduction-58/revisions-50 Let us know if you have any questions.

I definitely understand this request. On the other hand, personally I would not want SmartTag to turn back on if I'd turned it off. More thought required...

If you have SmartTag disabled, and you record a cue, you will immediately snap into the cue you just recorded, and the manually adjusted programmer values will be cleared automatically. As you have essentially done a GO Snap without running the cue's fade times, the Pause button will flash. Hope this helps.

Hi @SanCarlino Welcome to the forum. Jester consoles were discontinued back in 2017, and stocks of spare PCBs have now run out. So we can support from the user/software side, but cannot guarantee that the console can be repaired if something goes wrong. I would recommend working through the Jester ML Training Playlist here... Yes - the latest fixture library for Jester ML consoles is v41, and is available to download from the Jester webpage... https://www.vari-lite.com/global/products/jester-series If you need to control a fixture that is missing from the library, you can create a fixture file to load into the console using "Zero 88 Fixture Tools". This application can be downloaded here... https://vari-lite.s3.eu-west-1.amazonaws.com/software-firmware/Zero-88-Fixture-Tools-2.6.zip JesterOS 4.1 is the final version for Jester ML consoles, and is very stable. "Phantom Jester" is a Windows software package, that allows you to program and edit Jester show files on your PC. These show files can then be transferred to the console via USB. This can be downloaded from the link below... https://www.vari-lite.com/b-dam/vari-lite/discontinued-products/jester/english/phantom-jester-4-1.zip Hope this helps.

Intensity transitions between the steps of a chase can also be configured in ZerOS. See here for more information… https://www.zero88.com/manuals/zeros/cues-playbacks/chases/chase-settings#intensity

Try using the kaleidoscope colour effect, but reduce the size to reduce the saturation. If that’s too subtle try adding the candle effect too.

If you have made edits to intensities manually, they will be displayed in red in the Output window. These values will need to be cleared to allow your cues to output as recorded. You could enable "Programmer Time", so that double tapping CLEAR fades the fixtures to their cue values, instead of snapping them. See here for more information... https://www.zero88.com/manuals/zeros/z-key/z-encoders Hope this helps.

It is not currently possible to change the colours of the current and next cue. ZOS-8774 is logged on our system, to improve the clarity of the current versus next cue in the Cues window. I have raised the priority of this following your request. Please feel free to post your questions all in this thread. Although there is not a dedicated up to date Solution manual, I would recommend using the ZerOS manual for FLX series consoles here... https://www.zero88.com/manuals/zeros Hope this helps.

Tracking behaviour on Solution is identical to FLX. The HTP/LTP option on the Solution Special MFKs is only related to the channel faders. As these control intensity, it is not related to Colour, Beam, or Position. More information on Tracking here... https://www.zero88.com/manuals/zeros/cues-playbacks/record-options/tracking

Thank you for sharing your show file. The first observation is that this show file is from ZerOS 7.9.7, which is serval versions out of date. I would therefore recommend updating your console's software. ZerOS 7.14.1 is the latest software, and can be downloaded from the link below... https://vari-lite.s3.eu-west-1.amazonaws.com/software-firmware/ZerOS-7.14.1.exe Release notes including installation instructions are available here... https://vari-lite.s3.eu-west-1.amazonaws.com/graphics/technical/documents/ZerOS-7.14.1-release-notes.pdf Please update your console's software. As discussed, this sounds like a hardware issue. Start by cleaning the faders. If this doesn't clear the issue, the faders will need replacing.

Great - thanks for letting me know. Yes it would. However, if you have a Cue Stack on a playback, the playback's button will already be a Go button by default. Please let me know if you have any questions.

This is similar to Windows File Explorer - upon renaming a file, the file name will be selected. Tapping into the text/using the arrow keys, will allow you to edit/add to the existing file name, rather than replace it.

As @iank99 mentions, it sounds like fader 26 on your console is faulty. Please send us an email to support@zero88.com for detailed troubleshooting information. You may find that a small drop of switch/contact cleaner will resolve the issue. If it doesn't, fader 26 will need to be replaced. As you are in the UK, I would recommend contacting @iank99 to get this repaired... Without any further information, my first guess would be that this may be related to Speed Override. If you tap the Z/SHIFT key, you'll see Speed Override on the second encoder wheel. Please ensure this is reset to the midpoint position. If a yellow bar is shown, tap the button in the middle of the Speed Override encoder wheel, to reset. Upon running cues, the cue timings will then be used, and will not be temporarily overridden. To troubleshoot further, we would need to see a copy of the console's show file. If you can tap SETUP > Save, save the file to a USB drive, and email this to support@zero88.com, we'll take a look. Please let us know if you have any questions.

Hi @Harvey John Welcome to the forum. This is not possible. The DMX output ports on Gateway 8 are outputs only, meaning Gateway 8 can only convert Ethernet DMX back to physical DMX. Physical DMX cannot be converted to Ethernet DMX using Gateway 8. Please let us know if you have any questions.

Hallo Jens, Mein Kollege Keith hat auf Ihre E-Mail an support@zero88.com geantwortet. Bitte lassen Sie uns wissen, wenn wir Ihnen helfen können. Hi Jens, My colleague Keith has replied to your email to support@zero88.com. Please let us know if there's anything we can help with.

Excellent - pleased to hear that's stopped the effect from running. Please let us know if there's anything else we can help with.

Hi @Geoffc Welcome to the forum. Firstly, I'd recommend saving a copy of the console's current show file to a USB drive. That way, if you make any incorrect changes, you can then simply load in your previous show file from the USB drive. Please click the link below for information on saving show files... https://www.zero88.com/manuals/zeros/setup/save The effect therefore needs to stop in cue 21. Please follow this process to stop the effect: Go into cue 21, so that it is live and outputting (green row in the Cues window) Double tap CLEAR Select the fixtures running the effect. For example by using the buttons below the fixture's channel faders. Tap the "Effect" tab at the top of the internal touchscreen, and choose [No Effect]. The effect should stop. Then press-and-hold UPDATE, and you should see the Update Options appear on the internal touchscreen. In the Update Options, ensure that the SmartTag button is disabled, indicated with a blue stripe. If it has a red stripe, tap it to disable. If you cannot see a SmartTag button in this window, please see this link for more information - https://www.zero88.com/manuals/zeros/cues-playbacks/record-options Ensure that "Track Forwards" has a red stripe, rather than "Cue Only". With Track Forwards selected, you will send your "No Effect" instruction down through subsequent cues, therefore stopping the effect from running in those cues. Tap your Master Playback's GO button to complete the process. Then, press-and-hold RECORD, to open the Record Options on the internal touchscreen. Tap "SmartTag" and "Cue Only" again, to re-enable them (red stripe), and the console will then be back in the default programming behaviour. Tap RECORD again to save and close. I hope this helps. Please let us know if you have any questions.

That is correct. By "prepare", I mean triggering all programmed parameters to go to their defined values, prior to raising the intensity with the playback's fader. So: Colour, Beam, Shape, Position, & Effect values will be activated. That is correct. If you open the settings of a playback, you will only be configuring the behaviour of this single playback. Please click the link below for more information... https://www.zero88.com/manuals/zeros/cues-playbacks/playback-settings

Enabling/disabling SmartTag will affect what gets included when recording/updating. It does not affect cues that have already been recorded. To be selective of what does and what doesn't get recorded, you will need to work with SmartTag disabled. Please click the link below for more information... https://www.zero88.com/manuals/zeros/cues-playbacks/record-options/snapshot-smarttag#smarttag

Fixture file for the Varytec Event Par IP65 4in1 14x8w... Varytec Event Par IP65 4in1 14x8w.ift (We had already made this fixture file).