Jump to content
Vari-Lite Controls Support Forum

RCRLIGHTING

Regulars
  • Posts

    11
  • Joined

  • Last visited

Posts posted by RCRLIGHTING

  1. Hello All,

     

    I have 4 GLOW-LIGHTING Bumble Beams which in short is a Chinese knockoff of a Clay Paky Sharpy. I have tried using the Sharp Standard and Vector Profiles which seems to work...sort of. I tried to create a fixture profile but can't seem to get the configuration correct. Any help would be great.

     

    Manual attached in zip form

     

    Thank you in advance for your time.

     

    Reg

    Bumble-Beamâ„¢-User-Guide.zip

  2. Hello and Good Morning from Canada

     

    I received 2 used YISCOR CREE 12LED RGBW LED Moving Heads. I was not able to find a similar match to that fixture with the new version 30 of the fixture profiles I downloaded the other day.

     

    I tried to create one based on the DMX Values chart provided on line but does not seem to work when I load it into my Fat Frog console. Below are the DMX values listed....

     

    Channel DMX Value Function
    --------- ------------ ---------
    1 000-255 X 0-540°
    2 000-255 Y 0-180°
    3 000-255 X Fine 0-1.8°
    4 000-255 Y Fine 0-1.8°
    5 000-255 Dimmer (0-100%)
    6 000-255 Strobe (0-100%)
    7 000-255 Red (0-100%)
    8 000-255 Green (0-100%)
    9 000-255 Blue (0-100%)
    10 000-255 White (0-100%)
    11 000-255 Mixed Colour Change
    --------------------------------------------------------------------
    12 000-011 No Effect
    011-120 Jump Change
    121-180 Gradual Change
    181-244 Mixed Colour Effect
    245-255 Sound Active
    --------------------------------------------------------------------
    13 000-255 Adjust CH12 effect speed fast to slow
    14 000-255 Pan/Tilt Speed adjust fast to slow
    15 245-255 Reset
    More info and fixture can be seen at the following address:
    Any help creating this profile would be awesome.
    Thank You in advance for your .time.
    Rejean Frenette
    Toronto, Canada
  3. Good Morning kgallen,

     

    Every little bit helps in this case. I'm an old school LD and just recently over the last few years got back into the business. In short, my shows are not complicated. I work with a KISS Tribute, BON JOVI Tribute, Journey Tribute and soon to be a Fournier Tribute. Straight ahead rock & roll...nothing fancy. I think I will be able to get away with some additional topics you covered in this thread, it looks like I will have to start from scratch after the holidays....have lots of time until the shows start up again. Will let you know what happens......

     

    Rejean

  4. Thank You very much for the additional clarification. I rechecked the desk last night and this is the infor I have:

     

    Software Version: 10.12.1 (OS updated in 2013)

     

    Desk Setup:

    ---> Program Mode: FULL

     

    When I press the "-" button, the following information displays:

    ---> Mode: Partial

    ---> Tracking: ON

    ---> Replay Tag: Add

    ---> Brightness: All

    ---> Beamshape: Channel

    ---> Position: Channel

     

    I will mess around with this again tonight.

     

    Thank you for your time.

     

    Rejean

  5. I have a very large show this weekend. This past weekend I noticed some strange behavior with my fixtures.

     

    Example:

     

    - 3 Chauvet Par 56 LED's...1 assigned to fixture 1, 2 & 3

    - 4 Sharpy like movers

     

    The Sharpy like movers have all been programmed and built into the memory stack.

     

    So....

     

    memory #1 = HOME postion

    memory #2 = Yellow - Up Position

     

    LED's on Submaster 1-1 = Blue

    LED's on Submaster 1-2 = Green

    LED's on Submaster 1-3 = Yellow

     

    Transfer Movers from memory #1 to Submaster 1-12 = HOME

    Transfer Movers from memory #2 to Submaster 1-11 = RED - Up Position

     

    What is happening is what I have fader 1-11 up for that RED scene, that works ok....no issues.

     

    If I move fader or press button 1-1 or 1-2 or 1-3, the mover on 1-11 changes position and colour. The fixture goes from Yellow to O/W and moves tilt to a down position. This also changes the scene on Submaster 1-1 or 1-2 or 1-3 from it's programmed colour to O/W which is the default colour when the LED's are homed based on the fixture profile loaded into the console.

     

    In short, how do I correct this? Is there something I am doing wrong or do I have to create all the scenes with the movers and LED's then transfer the memory to Submaster?

     

    Any help would be great.

     

    Rejean

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.